LS-207-8 Salt Spray Tester(120类型)

LS-207-6 Salt Spray Tester
LS-207-4 Touched Screen Salt Spray Tester(120类型)
120 2

LS-207-8 Salt Spray Tester(120类型)

分类目录: ,

  • 描述
  • 查询

LS-207-8 Salt Spray Tester(120类型)

采用:

该机器具有标准化的测试方法来检查涂层样品的耐腐蚀性能. 盐雾试验是一种加速腐蚀试验，对涂层样品产生腐蚀作用，以预测其作为保护涂层的适用性. 腐蚀产物的出现 (氧化物) 一段时间后评价. 测试持续时间取决于涂层的耐腐蚀性; 涂层越耐腐蚀, 没有出现腐蚀迹象的测试时间越长. 不同的涂层在盐雾试验中表现不同，因此, 一种涂层的测试持续时间与另一种涂层的测试持续时间不同.

设计标准:ISO 9227、GB/T 2423.17-1993 ,GB/T 2423.18-2000、GB/T 10125-1997、ASTM.B117-97

贺H8502 ,IEC68-2-11、IEC68-2-52 1996 ,GB.10587-89,CNS.4158,CNS.4159,CASS,吨/吨 12967.3-91 中国社会科学院

 

LS-207-8 Salt Spray Tester(120类型)

规范:

内部尺寸1200×1000×500(长×宽×高)毫米
外形尺寸1900×1300×1400(长×宽×高)毫米
Test room temperatureNSS ACSS 35℃±1℃/ CASS 50℃±1℃
Pressure Barrel TemperatureNSS ACSS 47℃±1℃/ CASS 63℃±1℃
Laboratory capacity600大号
Salt water box capacity40大号
Compressed air pressure1.00±0.01kgf/cm2
Volume of spray1.0-2.0ml/80cm2.h
Laboratory relative humidity85%RH above

 

LS-207-8 Salt Spray Tester(120类型)

字符

1.Imported gray P.V.C board, special treatment resistant to corrosion.V – shaped frame and stainless steel tube Angle, make sure the test object into 30 degrees Angle, four wheels glide, can push to go.
2.Fine workmanship, beautiful appearance, high transparency, pneumatic open cover.
3.Automatic/manual water filling system is adopted, with the function of automatic/manual water filling when water level is insufficient.The experiment will not be interrupted to meet the diversified environmental requirements of the guests.(automatic water rehydration only needs to be connected to the water pipe.)
4.喷嘴: the spray tower is equipped with a cone disperser, which can guide fog, regulate the amount of fog, and even fog falling.
5.Use high-precision multi-function timer and the test time can be set to multi-function. With the power failure memory function, continue to work after the power failure, until the required time is completed, and avoid redoing the experiment after the power failure.
6.In the salt spray test, direct steam heating is adopted, the heating speed is fast, the temperature distribution is uniform, and the standby time is shortened.
7.Two-key automatic operation.With full trouble warning system.When the fault occurs, the light can be turned on and the buzzer will alarm.
8.Two internal fog collecting tubes are used.It is less likely to be damaged than the traditional outer-type.
9.With overload short-circuit protection.To prevent the damage of the instrument and its internal electronic control parts.
10.The inner and outer box is connected with the seal groove and sealed with water。
11.The imported temperature controller USES digital display，PID control，error±0.1℃。
12.强电磁辐射源：1：Test room temperature：35℃－－Pressure barrel temperature：50℃（can set）

2：Test room temperature：47℃－－Pressure barrel temperature：63℃（can set）

13.The refill bottle is made of recessed water level window, which is easy to clean.
14.Heat speed：1：Test room，RT－－-→35℃ About 35minutes

2：Pressure barrel，RT－－-→47℃ About 15minutes

15.温度精度：±1℃
16International standard：RELATEU STANDARDS CNS 3627、3885、4159、7669、8866； JIS D-0201、H-8502、H-8610、K-5400、Z-2371、ISO3768、3769、3770； ASTM B-117、ASTM B-268 B-268、GB-T2423、GJB150。

联系我们





相关产品