- Опис
- Упит
LS-101-1 Melt Flow Index Tester
Discription:
Melt flow rate testing instrument can be used for ABS, polystyrene, polyethylene, polypropylene, polyamide, fiber resin, acrylate, POM, fluorine plastic, polycarbonate and other plastic materials, the melt flow rate (MFR) or the melt volume flow rate (MVR) to be determined.
Стандард:
GB/T3682-2018,ISO1133-2011, ASTM D1238
LS-101-1 Melt Flow Index Tester
Product Character:
1.English LCD Touched Screen.Ø
2.Hand automatic cutting material.
3.Double temperature control system, temperature control precision is more accurate, higher heating efficienc
4.Double imported sensors, more accurate temperature gradient from top to bottom, can be used independently, and improve the service life.
- Cylinder for imports hartz alloying nitriding treatment, opening mould for carbon tungsten steel material, material reality.
6.Insulation barrels of sus304 stainless steel material for the whole, long-term high temperature does not rust.
7.Automatic calculation results, and print.
Test Methods:MFR Methods
Display Mode:English color touch screen display
LS-101-1 Melt Flow Index Tester
Спецификација
Модел | LS-101-1 |
Barrel parameters | Inner hole 9.550±0.005mm |
Pistons parameters | Piston head: 9.474±0.005mm |
Outlet length | 8.000±0.025mm |
Paramters | Extrusion hole 1=2.095±0.005mm |
Temperature parameter | With intelligent temperature control instrument, with four pairs of significant temperature setting control, PID parameters can be automatically set, precision up to ± 0.1 degree centigrade |
Распон температуре | Room Temperature~450degree centigrade |
Temperature fluctuation | ±0.2 ℃ |
Temperature uniformity | ±1℃ |
Резолуција приказа температуре | 0.1℃ |
Display resolution | 0.1℃ |
Maximum comsuption | < 600В |
Time display resolution | 0.1с |
Weight parameters are as follows: | |
Weight accuracy | ±0.5% |
Basic configuration
| A 0.325kg |
B 1.2kg | |
C 2.16kg | |
D 3.8kg | |
E 5kg | |
F 10kg | |
G 12.5kg | |
H 21.6kg | |
Position detection | |
Loop distance from up and down | 30мм |
Control precision | ± 0.1mm |
Test flow control | |
Times of cutting the material | 0~10 times |
Material cutting interval | 0~999s(set reference Table 2) |
Control flow reaches the set temperature without volatility | |
Barrel temperature time | 15 мин. |
Material be installed | 1 мин. |
Material sample temperature recovery time | 4 мин. |
When binder set | 1мин |
Output mode | Micro-automatic print output |
Cut material methods | The hand automatic cut into one body |
Test load | Eight sets of weights |
Снага | AC220V±10% 50/60HZ |
Accessories List
Не | Име | Кол | Напомена |
1 | Тежина | 1 комплет | 0.325㎏、0.875㎏、1.835㎏、2.5㎏、2.915㎏、3.475㎏、4.615кг、5.0k g |
2 | Weight tray | 1ком | Within level 1 оптерећење |
3 | Charging hopper | 1ком | |
4 | Mouth mold cleaning rod | 1ком | |
5 | Charging bar | 1ком | |
6 | Cylinder cleaning rod | 1ком | |
7 | piston rod | 1ком | |
8 | mouth mold | 1ком | |
9 | gauze | 2roll | |
10 | Print paper | 2 roll |
Standard test force(8 level)
1 ниво:0.325 kg=(piston rod+weight tray+heat insulation cover+No 1 weight)
=3.187N
2 ниво:1.200 kg=(0.325+No2 0.875 тежина)=11.77 N
3 ниво:2.160 kg=(0.325+No3 1.835 Тежина)=21.18 N
4 Level:3.800 kg=(0.325+No4 3.475Weight)=37.26 N
5 Level:5.000 kg=(0.325+No.5 4.675Weight)=49.03 N
6 Level:10.000 kg=(0.325+No.5 4.675weight+No.6 5.000Weight)=98.07 N
7 Level:12.000 kg=(0.325+No.5 4.675weight+No.6 5.000+No.7 2.500weight)=122.58 N
8 ниво:21.600 kg=(0.325+No.2 0.875weight+No3. 1.835+No.4
3.475+No.5 4.675+No.6 5.000+No.7 2.500+No.8 2.915weight)=211.82 N
Chart 1
Melt flow rate (g/10min) | Sample quality in charging barrel (г) | Extrudate cutting-off interval time (с) |
0.1-0.5 | 3-5 | 240 |
>0.5-1 | 4-6 | 120 |
>1-3.5 | 4-6 | 60 |
>3.5-10 | 6-8 | 30 |
>10 | 6-8 | 5-15 |
1. If this experiment value is less than 0.1 г / 10 min or greater than 100 г / 10 мин, suggest you melt flow rate
|
Chart 2
Material | Test temperatureθ,℃ | Standard load mnom,кг |
PS | 200 | 5.00 |
PE | 190 | 2.16 |
PE | 190 | 0.325 |
PE | 190 | 21.60 |
PE | 190 | 5.00 |
PP | 230 | 2.16 |
ABS | 230 | 10.00 |
PS-1 | 200 | 5.00 |
E/VAC | 150 | 2.16 |
E/VAC | 190 | 2.16 |
E/VAC | 125 | 0.325 |
SAN | 220 | 10.00 |
ASA、ACS、AEC | 220 | 10.00 |
PC | 300 | 1.2 |
PMMA | 230 | 3.8 |
PB | 190 | 2.16 |
PB | 190 | 10.00 |
POM | 190 | 2.16 |
MABS | 220 | 10.00 |